Close
Russia Moscow
8(964)777-40-29 order@rus-mil.com
Open hours: Mon - Sat 00.00 - 00.00

Plate carrier "Pantsir" with quick release system

(1 customer review)

104.14$110.65$

The cover is made of fabric with a density of 1000 D 100% polyamide with a polyurethane coating. Lining and internal pockets of fabric with a density of 600 D 100% polyamide. The weight of a cover is 1 kg 110 grams.

Clear
SKU: N/A Categories: , , Tag: Product ID: 9092

You may also like…

Description

Plate carrier "Pantsir" with with quick release system


KAP (Climatic shock absorber) is NOT INCLUDED in the kit !!!

Cover for carrying armored panels PANTSIR
The cover is designed to carry armor plates GRANITE, SAPI, aramid screens, does not hinder the movement of a serviceman due to the minimum area and weight, while protecting the most vital organs. The small size of the cover improves body ventilation in high temperature and humidity conditions. The cover consists of panels interconnected by straps, each with two inner compartments and a belt.

Outside, the cover is trimmed with horizontal straps for fastening the PALS system (MOLLE): 40 cells on the front panel, 48 cells on the back panel, 36 cells on both belt grips. Cell width 35 – 40 mm. On the lining of the front and back panels, a soft piece of basswood is sewn to fasten the cap and protect the neck At the bottom there are belt loops for attaching protection of the lower abdomen and groin, lower back.

For attaching patches, the front and back panels are trimmed at the top with a soft part of the "linden". For evacuation, a reinforced flat loop from a 50 mm wide belt is sewn over the linden tree on the back panel. All loaded elements of the cover are sewn with a special stitch – a zigzag.

According to the height, the cover is fitted with belts, 40 mm wide, threaded into the double-slot buckles, sewn at the top of the back panel. In front, the straps are fastened to the panel with a double-layer linden buckle with belt flags for easy unbuttoning with gloves.

For quick adjustment of the tape, you can simply fasten it to the side wall of the buckle and fasten it to the linden, which it is trimmed with on both sides. The strap belts are threaded into the pads, which are attached to them with a "linden" and serve to fix the cables of radio stations, hoses for drinking systems and have a soft pad 10 mm thick below which removes the "cutting" load from the belts from the shoulders when the case is fully loaded.

In addition, cables and hoses are fixed with detachable loops on the sides of the soft pads, front and rear panels. The mouthpiece of the drinking system is attached with a vertical loop made of tape, which is fastened to the “linden” at the top in the middle of the front panel. The same belt loop and narrow horizontal bottom flap in the front can be used to secure a small flat administrative pouch.

The size of the cover is fitted with a belt of two loops, which are attached to the front panel with "linden" with loops of hand tape, and at the back using two elastic cords with stoppers. At the front, the belt attachment point is closed by a large flap with an inner pocket, in which you can attach a flat pocket for three AK magazines to the "linden" or put papers and property there.

The left and right loops of the belt are attached with elastic cords with stoppers to the back panel; for this, horizontal strips with PALS (MOLLE) fastening cells are sewn there or connected together by removing the second cord. The place where the girths are attached to the back panel is closed with a large flap, which is wrapped 10 cm inward into a pocket for the plate, after which a valve is attached to it, on which the bottom of the plate rests.

Both grips have full-length internal pockets to accommodate side plates or aramid shields. The plates are fixed from above with flaps, which are fixed in linden pockets and can be moved or removed when not in use. Additional protection can be placed in internal mesh pockets from the inside out. Mesh pockets have attachments for side caps.

KAP (Climatic shock absorber) is NOT INCLUDED in the kit !!!

Case dimensions (size L):
Front panel height 400 mm,
Rear panel height 420 mm;
Front panel length – 300 mm;
Back panel length 310 mm;
Width (without K.A.P.) – 30 mm;
The height of the side girths of the belt is 150 mm, with valves – 240 mm;
The length of the lateral girth of the belt is 550 mm;
The weight of the cover (size L) without armor plates and aramid screens made of 1000D fabric is 1 kg 600 grams.


Shipping: shipping worldwide. (2-5 weeks)

Delivery: ships within 1-3 days after receiving cleared payment.

Payments: PayPal


paypal-verified

Additional information

Weight 1.6 kg
Dimensions 20 × 20 × 20 cm
Pattern

Olive, Multicam, Black, A-tacs FG, Spectre, Spectre SKVO, EMP

Size

L, M

1 review for Plate carrier "Pantsir" with quick release system

  1. delaitre paul

    I bought it in original spectre, nothing to say very good quality I hope it will be possible to buy more spectre original (this is my favorite camouflage!)
    Thank you very much
    Paul from France

Add a review

Your email address will not be published. Required fields are marked *